Month: January 2018

For many years, Webcon has supplied the finest quality DCOE mounting cups and grommets individually to allow some flexibility in the carburettor’s mounting. These are now available in handy complete carburettor sets.
The cup washers are manufactured to a very specific thickness and depth and yellow passivate coated. The grommets are manufactured to Webcon’s very specific levels of hardness and flexibility. Both parts are designed to offer outstanding performance in the most demanding of conditions and should not be confused with inferior versions that are on the market.

Part number 9900557100W4 is priced at £9.91 plus vat

Available directly from Webcon and from appointed Webcon dealers around the world.

For further details contact Webcon UK on +44 (0)1932 787100 or visit www.webcon.co.uk

Webcon now manufactures a heat shield for use on the Weber DCOE and DCO/SP range of carburettors.

On non-crossflow engines the carburettors are directly above the exhaust manifold. When exhaust heat rises up it can cause fuel handling problems in sidedraft carburettors. The new Webcon Heat Shield helps alleviate these problems by deflecting the heat around the carburettor.

The new Webcon Heat Shield is superbly made in the UK from 1.6mm Stainless Steel.

The part number 9990398700 is stamped with the Webcon logo to easily distinguish it from the thinner, less effective copies on the market.

The new Webcon Heat Shield retails at £14.95 plus vat. One heat shield is required per carburettor

Available directly from Webcon and from appointed Webcon dealers around the world.
For further details contact Webcon UK on +44 (0)1932 787100 or visit www.webcon.co.uk

Powerflex has just launched a number of front suspension parts for the VAG family of SUV PL71 platform based vehicles: VW Touareg, Porsche Cayenne and Audi Q7.

Although replacement OE bushes are available, the original parts commonly fail due to high torsional loads and the natural degradation of rubber which, on a big heavy vehicle such as these can lead to imprecise steering, braking instability and expensive uneven tyre wear. By replacing the worn rubber parts with the Powerflex polyurethane bushes you can experience immediate and lasting improvements to these problems.

PFF85-1601 Front Lower Wishbone Front Bush: £55.08 pair
PFF85-1602 Front Lower Wishbone Rear Bush – for cast aluminium wishbones: £65.88 pair
PFF85-1702 Front Lower Wishbone Rear Bush – for cast steel wishbones: £58.68 pair
PFF85-1604 Front Wishbone Upper Bush: £102.96 per set of 4. All prices incl. VAT

For vehicles used in motorsports or predominately on track these parts are also available in the Powerflex Black Series range which is manufactured using a 95 Shore A compound that boasts 25% increased stiffness over the Powerflex purple 80 Shore A performance material.

All Powerflex bushes, of course, carry a Lifetime Warranty.
For more details visit www.powerflex.co.uk or call 01895 460033.

Powerflex is pleased to announce its new front suspension bushes for the Honda Civic Mk10 2016 onwards.

PFF25-1001 Front Arm Front Bush is developed using our 95A durometer material that boasts 25% increased stiffness over the Powerflex purple 80 Shore A performance material which helps to improve handling and braking stability. Retail price: £59.98 per pair incl. VAT

PFF25-1002 Front Arm Rear Bush is a dual-durometer design that allows free rotation, that avoids torsional twist in the material which is the main cause of failure for the OE rubber bush.
Retail price: £86.28 per pair incl. VAT

Powerflex bushes aren’t just performance upgrade products. Powerflex bushes commonly serve as fit-and-forget replacement solutions with a Lifetime Warranty for added peace of mind.

For more details visit www.powerflex.co.uk or call 01895 460033.

Powerflex is pleased to announce a new engine mount insert to fit vehicles from the VAG PQ35 platform range including the VW Golf 5 & 6, Scirocco, Jetta, Passat, Audi A3, S3 and TT as well as many others. (A full listing can be found on the Powerflex website)

The original rubber mount often degrades and softens over time, allowing excessive movement of the engine that leads to a premature failure. Up until now the only options have been to replace the worn out mounts with new standard mounts or upgrade to expensive aftermarket mounts that promote excessive NVH levels.

The Powerflex insert is an easy-to-fit intermediate solution to the above-mentioned problems.

PFF85-532 Upper Engine Mount Insert is designed to fit into the void in the original rubber mount to stiffen it and minimise unwanted engine movement. £34.50 incl. VAT

For vehicles used in motorsports or predominately on track these parts are also available in the Powerflex Black Series range which is manufactured using a 95 Shore A compound that boasts 25% increased stiffness over the Powerflex purple 80 Shore A performance material.

All Powerflex bushes, of course, carry a Lifetime Warranty.
For more details visit www.powerflex.co.uk or call 01895 460033.

Moss Europe has announced new 5 speed gearbox conversion kits for the MGA and MGB.

The kits are based on a brand new Mazda MX-5 gearbox and give the MGA and MGB the slick gear changes that have become synonymous with the MX-5, together with a 5th gear for relaxed cruising.

The kits are supplied with a fully assembled gearbox with a bespoke cast bell housing and casing designed to fit directly to the MG’s engine back plate. The bell housing flange has been designed to resemble the standard gearbox thus preserving engine bay originality.

Each conversion kit uses the flywheel applicable to the engine, an appropriate clutch cover and a Mazda OE clutch plate. The installation on the MGA does require the removal of existing gearbox mounts and the enlarging of the gearbox tunnel aperture but for the MGB there is neither cutting nor permanent modifications required. Full instructions are included.

Kits include: • Brand new Mazda 5 Speed gearbox assembled into custom casing & bell housing • Concentric clutch slave cylinder assembled with pipework • Mazda OE clutch plate • Mazda OE gear knob • Custom gearbox mountings • Speedo drive & cable • Bespoke propshaft • all parts & hardware required for installation. The gearboxes are prefilled with SAE 75W-90 oil.

Kits are available for high and low starter MGAs, 3 bearing MGB 1962-65 and 5 bearing MGB 1965-68. All retail at £2,700.00. Kits are also available for cars with engine conversions.

For more details contact Moss Europe Ltd, on +44 (0) 20 8867 2000
or visit their website: www.moss-europe.co.uk

The heritage of MOMO is reborn with the MOMO Indy Heritage steering wheel.

The MOMO Indy Heritage is traditionally finished in beautiful mahogany wood with a glossy finish. The 350mm diameter rim is accented with brushed aluminium spokes and the iconic Heritage MOMO Logo is featured on the horn button and engraved on the bottom spoke to leave no one in any doubt as to this wheel’s pedigree.

This beautiful classic wooden steering wheel reflects the true heritage of MOMO, harking all the way back to the company’s beginnings in 1964. Class, quality and style!

Retail Price £242.39 inc VAT.

For more details contact Brown & Geeson Ltd.
+44 (0) 1268 764411 or visit their website: www.momo-uk.co.uk

Mini Spares has just released two complete black wiper kits for all classic Minis.

The kits use wiper arms with the hook style of blade attachment which was introduced on 1990 Minis but the spindle fitting remains the same as earlier models allowing this kit to be used to upgrade a wide range of models.

The blades are the 11″ GWB911 blade made by Bosch which Mini Spares has found to be the best available for the Mini.

The kits contain two wiper arms and two wiper blades with rubbers and are available in right and left hand drive version.

For RHD (LH Park) order as DKB101480KIT at £21.00 incl. VAT and for LHD (RH Park) order as DKB101490KIT at £21.00 incl. VAT.

For more details contact Mini Spares on
+44 1707 607700 or visit their website: www.minispares.com

Mini Spares has just released a multi-layer steel (MLS) head gasket that is suitable for both full race and high performance road applications. The MLS gasket is especially suitable for 8 Port and 5 Port alloy applications because these gaskets do not use fire rings which can damage the soft alloy surface.

The gasket is for 73.5mm bore and is 30mm thick.

Retail price is £62.95 inc VAT.

For more details contact Mini Spares on
+44 1707 607700 or visit their website: www.minispares.com

M-Style is pleased to announce its new ‘M-Look’ Front Bumper for the F16 X6.

The complete package includes: the bumper moulding itself with washer jet cover panels; upper, lower, left and right wave pattern grilles; a pair of grille trims; steel internal panels and braces and even a UK sized front number plate mounting panel.

The kit retails at £869.00 and comes ready for painting.

M-Style can also provide a painting service at £210 and a painting and fitting service at £280.
All prices include VAT.

For further details visit the M-Style website:
www.mstyle.co.uk or call 0208 5989115